Motrona - Speed Monitors
Monitors for speed, Direction of Rotation, standstill, position, slip and shaft fracture.
Motrona is having range of Speed/Position monitors, are able to measure speed and compare with preset values to detect lower or over speed, direction of rotation or standstill of system to protect from undesired start of machines.
A speed / position monitor is used to monitor and analyze speeds to take measures for preventing risks and damage like misalignment, shaft breakage, torsion and slippage.
Typical applications in which a speed / position monitor is used are the following:
• Cranes (gantry crane, overhead crane, process crane, single / double girder overhead traveling crane, retrofit)
• Wind turbines
• High rack storage systems
• Transport systems and conveyor systems
• Saws/ woodworking machine
• Test benches
• Balancing machines, grinding machines, agitators, filling machines and many more.
Special models of the speed monitors, which have an Analog / Relay output, can also be used for control tasks.
Special models of the speed monitors, which have an Analog / Relay output, can also be used for control tasks.
Motrona Speed Monitor
DZ210: Direction and Standstill Monitor
Electronic monitor for monitoring left / right rotation and standstill. With universal pulse inputs for all common incremental encoders and sensors.
- Pulse input with format A, B, 90° [HTL] or A, /A, B, /B [RS422],
also possible for single channel - Input frequency up to 500 kHz
- 2 output relays with potential-free change-over contact and
2 transistor outputs with High-Side-Driver, short-circuit-proof, [7 … 30 VDC] - Power supply 17 … 30 VDC
- Snap-on housing for top hat rail (according to EN 60715)
- DIL switch for setup of input characteristic and definition of standstill
DZ260: Speed Monitor with 3 Output Relays and Analog Output
Compact device for monitoring overspeed, underspeed, standstill and direction of rotation with universal inputs for incremental encoders, proximity switches, light barriers or sensors.
- Pulse input with format A, B, 90° [HTL] or A, /A, B, /B [RS422],
also possible for single channel - Input frequency up to 1 MHz
- 3 output relays
- 14 Bit analog output for ±10 V or 0/4 … 20 mA
- Power supply 17 … 30 VDCAuxiliary voltage output +5 V for the supply of TTL encoders
- Snap-on housing for top hat rail (according to EN 60715)
LCD display, backlighted - Setup via keys or via PC by serial RS232 interface
Motrona Position Monitor
ZD640: Position monitoring, monitoring of misalignment, shaft breakage, torsion and slippage.
- 4 control inputs for PNP / NPN / Namur signals [10 … 30 VDC]
Input frequency up to 1 MHz - scalable inputs with format A, /A, B, /B [HTL / TTL / RS422,
single channel, dual channel, symmetric or asymmetric] - 4 fast transistor outputs with push-pull characteristic,
short-circuit-proof [5 … 30 VDC] - 4 potential-free output relays
- The slip monitor builds the difference between both encoders and
compares these with signs including the 4 adjustable switching thresholds - The 4 programmable limit values ??switch the output relays or transistor switch outputs as a function of the determined position difference
- A switchable time-controlled reset function also allows the monitoring of slip with definable values for nominal slip
MS640: Motion monitor for secure and redundant control of two drive trains.
- 2 Pulse inputs with format A, B, 90° [HTL] or A, /A, B, /B [RS422]
- 4 control inputs for PNP / NPN / Namur signals [10 … 30 VDC]
- 6 logical inputs for PNP signals [10 … 30 VDC]
- Input frequency up to 500 kHz
- 4 fast transistor outputs with push-pull characteristic,
short-circuit-proof [5 … 30 VDC] - 4 forced-guided redundant output relays with potential free change-over contact
